BRCYX - 1783 BAY COUNTRY LATEX SEMI-GLOSS WHITE
- MSDS: BRCYX
- Manufacturer: BRUNING PAINT CO INC
- Product Name: 1783 BAY COUNTRY LATEX SEMI-GLOSS WHITE
- National Stock Number: 8010-00F028045
Product Identification
Product ID:1783 BAY COUNTRY LATEX SEMI-GLOSS WHITE
MSDS Date:10/08/1989
FSC:8010
NIIN:00F028045
MSDS Number: BRCYX
Responsible Party
BALTIMORE, MD 21224-4347
US
Emergency Phone: 301-342-3641
Info Phone: 301-302-342-3636
Cage: EO376
Contractor
Telephone: 800-368-2076
Cage: 85520
Ingredients
ETHYLENE GLYCOL, GLYCOL
CAS: 107-21-1
RTECS: KW2975000
Fraction By Weight: 2.06%
ACGIH TLV: C 127 MG/CUM
EPA Report Quantity: 1 LB
DOT Report Quantity: 1 LB
9.7
RTECS: 9999999WG
1.136
RTECS: 9999999VO
Hazards
Routes of Entry: Inhalation:YES Skin:NO Ingestion:NO
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:EYES: IRRITATION.
Explanation of Carcinogenicity:NONE
Effects of Overexposure:INHALATION: PERMANENT BRAIN & NERVOUS SYSTEM
DAMAGE.
First Aid
First Aid:EYES/SKIN: FLUSH W/LUKE WARM WATER FOR 15 MINS. INHALATION:
REMOVE TO FRESH AIR. RESTORE BREATHING IF REQUIRED. INGESTION:
RINSE MOUTH IMMEDIATELY. GIVE EXPOSED INDIVIDUAL 6 TO 8 OUNCES OF
LIQUID. NEV ER GIVE ANYTHING BY MOUTH TO AN UNCONSCIOUS PERSON.
DON'T INDUCE VOMITING UNLESS ADVISED BY A PHYSICIAN. OBTAIN MEDICAL
ATTENTION IN ALL CASES.
Fire Fighting
Flash Point Method:TCC
Unusual Fire/Explosion Hazard:CONTAINERS EXPOSED TO HEAT FROM FIRES
SHOULD BE COOLED W/WATER TO PREVENT VAPOR PRESSURE BUILD UP WHICH
COULD RESULT IN CONTAINER RUPTURE.
Accidental Release
Spill Release Procedures:DON'T FLUSH TO SEWER, WATERSHED, OR WATERWAY.
Handling
Handling and Storage Precautions:KEEP FROM FREEZING. DON'T STORE >120F.
DON'T TAKE INTERNALLY. CLOSE CONTAINER AFTER EACH USE. KEEP OUT OF
REACH OF CHILDREN.
Other Precautions:DON'T BREATHE VAPORS OR SPRAY MISTS. INTENTIONAL
MISUSE BY DELIBERATELY CONCENTRATING & INHALING THE CONTENTS MAY BE
HARMFUL OR FATAL.
Exposure Controls
Respiratory Protection:IN OUTDOOR OR OPEN AREAS USE NIOSH/MSHA APPROVED
MECHANICAL FILTER RESPIRATOR TO REMOVE SOLID AIRBORNE PARTICLES OF
OVERSPRAY DURING SPRAY APPLICATION. IN RESTRICTED VENTILATION AREA
USE A NIOSH/MSHA CHEMICAL MECHANICAL FILTERS. SEE SUPP.
Ventilation:PROVIDE GENERAL DILUTION OR LOCAL EXHAUST IN VOLUME &
PATTERN TO KEEP BELOW TLV.
Work Hygienic Practices:REMOVE/LAUNDER CONTAMINATED CLOTHING BEFORE
REUSE. WASH HANDS THOROUGHLY BEFORE EATING OR USING WASHROOM.
Supplemental Safety and Health
CON'T RESPIRATORY PROTECTION: IN CONFINED AREAS USE NIOSH/MSHA APPROVED
AIR LINE TYPE RESPIRATORS OR HOODS. PERCENT VOLATILE BY WEIGHT:
63.74.
Chemical Properties
Boiling Pt:B.P. Text:212-490F
Vapor Pres:17
Vapor Density:>1
Evaporation Rate & Reference:SLOWER THAN BU AC
Percent Volatiles by Volume:73.4
Stability
Stability Indicator/Materials to Avoid:YES
STRONG ACIDS
Stability Condition to Avoid:FREEZING, TEMPS >120F
Hazardous Decomposition Products:CO, CO2, & OXIDES OF NITROGEN
Disposal
Waste Disposal Methods:DISPOSE OF IN ACCORDANCE W/LOCAL, STATE, &
FEDERAL REGULATIONS.
Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.